Furuno FCV • User guide • Download PDF for free and without registration!. Furuno Color LCD Sounder FCV/ User Manual • Specifications, Furuno • Furuno Sports and recreation. User guide • Read online or download PDF • Furuno FCV User Manual • Furuno Air equipment.
|Published (Last):||18 September 2007|
|PDF File Size:||5.11 Mb|
|ePub File Size:||19.82 Mb|
|Price:||Free* [*Free Regsitration Required]|
Do not remove the label. To avoid electrical shock, do not Warning Label 1 remove cover. The installer of the equipment is solely responsible for the proper installation of the equipment.
Use the specified power cable. This dedication to excel- lence is furthered by our extensive global network of agents and dealers. After the com- pletion of the equipment check, the last-used display appears.
Rotate the MODE knob again to choose the display mode desired. The screen you chose appears soon there- after. Single frequency display Low frequency 50 kHz The sounder uses ultrasonic signals to detect bottom conditions.
The lower the frequency of the signal, the wider the detection area.
This mode is useful for determining bottom contour. When the bottom depth increases, the display automatically shifts to keep the bottom echo at the lower part of the screen. Choosing Range The basic range may be chosen in Auto or Manual mode. Range Auto Manual 15 ft 30 ft 60 ft These are ft available with ft Manual mode.
Generally, use a higher gain setting for greater depths and a lower setting for shallower waters. Incorrect gain may produce wrong manua, indication, possibly resulting in a dangerous situation. You may also use to move manuwl cursor. The selected setting box or window appears. This is mainly due to sediment in the water or noise. These can be suppressed by adjusting Clutter on the menu. Clutter cannot be adjusted when Fishing or Cruising is selected on the Auto Gain setting window.
It is useful for estimating the kind of turuno school and bottom composition. In the dual frequency display, the A- Scope display is only available with the high fre- quency display. Note that the bottom lock display must be turned on to use vuruno alarm. Use to set the range of depth, tem- perature, speed or distance as appropriate. To shorten the alarm range marker use and to lengthen use For the bottom alarm, temperature alarm, speed alarm or guruno alarm, press the ENTER key to finish, and then go to step Quit Waypoint setting window Note1: Cancel Bottom Zone setting window 2.
Furuno FCV User Manual | 57 pages | Also for: FCV
Use to choose the border desired Above or Below. Off Window Size Battery: Data menu This menu mainly sets up how to display data input by external equipment.
Data Go to WPT: Off Data Box 2: This menu has nine sub menus. To dis- play each sub menu, do the followings. Units Menu Units Depth: Only qualified personnel should work inside the equipment.
Maintenance Regular maintenance is essential for good performance. Checking the items listed in the table below monthly will help keep your equip- ment in good shape for years to come. Troubleshooting The table below provides basic trouble- shooting procedures which the user may follow to restore normal operation.
The indication goes higher with clockwise rotation; lower with counterclockwise rota- tion. The knob corre- sponding on-screen circle “lights” in red if the knob is normal.
Rotate the knob, and corresponding on-screen circle “lights” When choosing a location keep manial following in mind: When the boat has a keel, the transducer should be at least mqnual cm away from it. With the boat hauled out of mwnual water, mark the location chosen for mounting the trans- ducer on the bottom of the hull.
Furuno FCV-620 Manuals
Do not use this method on an inboard motor boat because turbulence is created by the propeller ahead of the trans- ducer.
Fuguno preparation Support the transducer with a piece of wood to keep it in place while it is drying. Let the transducer dry hours. For single drive boat, mount on the starboard side at least 75 mm 3″ beyond the swing radius mabual the propeller.
For twin drive boat, mount between the drives.
If the bracket has been temporarily fas- tened to the transom, remove it. Screw the bracket to the hull. Position the two cable clamps and fasten them in place. If used, push the cable cover over the cable and screw it in place.
Route the cable to the instrument being careful not to tear the cable jacket when passing it though the bulkhead s and other parts of the boat. The sensor does not have to be installed perfectly per- pendicular; however, the location should not be such that the transducer may be damaged when the boat is dry-docked. Fuse holder Power supply lines red and black Cable tie How to fix fuse holders Establishing the ground The ground wire 1. The signal line ground is isolated from the chassis ground, however the power line is not insu- lated.
For connecting two transducers Fabricating the transducer cable Fabricate the transducer cable as below and connect it to the matching box. Page of 56 Go.
Table of Contents Add to my manuals Add. Furuno color sounder operator’s manual model fcv pages. Page 4 The installer of the equipment is solely responsible for the proper installation of the equipment.
Shifting Range the menu window left is displayed to gray. Suppressing Low Level Noise 1. Setting Up Nav Data Displays 1. Page 28 Data menu This menu mainly sets up how to display data input by external equipment.
Troubleshooting Troubleshooting The table below provides basic trouble- shooting procedures which the user may follow to restore normal operation. Thru-hull Mount Transducer 4. Transom Mount Transducer 4. Page 40 Note 3: Power Connector Fuse holder Power supply lines red and black Cable tie How to fix fuse holders Establishing the ground The ground wire 1.
Iec Data Sentences 4. This manual also for: Comments to this Manuals Your Name. Enter text from picture: By pressing ‘print’ button you will print only current page. To print the manual completely, please, download it. Don’t show me this message again. Got it, continue to print. Don’t have an fcc